The diagram shows part of the vernier sc...

The diagram shows part of the vernier scale on a pair of calipers Which reading is correct

2.74cm

3.10cm

3.26cm

3.64cm

Text Solution

Verified by Experts

The correct Answer is:

VS `=4 MS = 2.7`
`MS +VS xx LC`
` 2.7 + 0.04= 2.74`

Topper's Solved these Questions

MASTER PRACTICE PROBLEM
BANSAL|Exercise Comphrehension|134 Videos
MASTER PRACTICE PROBLEM
BANSAL|Exercise Reasoning|75 Videos
FLUID MECHANICS
BANSAL|Exercise PYQS AIEEE|10 Videos
SEMICONDUCTORS
BANSAL|Exercise CBSE Question|32 Videos

Similar Questions

Explore conceptually related problems

The diagram below shows part of the main scale and vernier scale of a vernier callipers, which is used to measure the diameter of a metal ball. Find the least count and the radius of the ball. .

What is the reading of vernier scale shown in figure?

The least count of a vernier calipers 'X' is 0.01 cm. If the number of divisions on the vernier scale of another vernier calipers 'y' is double of that in 'X' , then the least count of 'Y' is _______ mm. (in both instruments 1 M.S.D. = 1mm)

The least count of a vernier calipers is 0.025 mm . If the 12th division of the vernier scale coinciles with a main scale division and the zero of the vernier scale is to the right of the zero of the main scale then the zero error is "______"

The least coun of a vernier calipers is 0.01 cm and if the zero mark of the vernier scale is right of zero of the main scale and the vernier coincidence is 7 when the jaws are in contact then the zero error is "_______" cm.

While measuring the diameter of a sphere using a vernier calipers the main scale reading was found to be p while the vernier coinciding division was q. If the least count of the instrument is r, then the radius of the sphere is given by the expression ________.

The internal jaws of a vernier calipers were held tightly inside a hollow tube when the zero of the vernier scale showed a reading of 1.9 cm and the 18th division on the vernier scale. The thickness of the wall of the tube is 1 mm. If M.S. D. = 1 mm and the number of division on the vernier scale is 20, find the outside diameter of the hallow tube.

BANSAL-MASTER PRACTICE PROBLEM-Additional topic

The diagram shows part of the vernier scale on a pair of calipers Whic...
Text Solution
|
The manifestation of band structure in solids is due to
Text Solution
|
When p-n junction diode is forward biased then
Text Solution
|
If the ratio of the concentration of electron to that of holes in a se...
Text Solution
|
If the lattice constant of this semiconductor is decreased, then which...
Text Solution
|
In the following, which one of the diodes is reverse biased ?
Text Solution
|
The circuit has two oppositively connected ideal diodes in parallel wh...
Text Solution
|
If a p-n junction diode, a square input signal of 10 V is applied as s...
Text Solution
|
In the circuit below, A and B represents two inputs and C represents t...
Text Solution
|
A p-n junction (D) shown in the figure can act as a rectifier. An alte...
Text Solution
|
The logic circuit shown below has the input waveforms ‘A’ and ‘B’ as s...
Text Solution
|
The combination of gates shown below yields .
Text Solution
|
Truth table for system of four NAND gates as shown in figure is : .
Text Solution
|
In semiconductor the concentrations of electron and holes are 8xx10^(1...
Text Solution
|
A potential difference of 2V is applied between the opposite faces of ...
Text Solution
|
The main cause of avalence breakdown is
Text Solution
|
A cube of germanium is placed between the poles of a magnet and a volt...
Text Solution
|
In the given figure, which of the diodes are forward biased?
Text Solution
|
Current in the circuit will be
Text Solution
|
The diode used in the circuit shown in the figure has a constant volta...
Text Solution
|
In the following circuits PN-junction diodes D(1), D(2) and D(3) are i...
Text Solution
|