Home
Class 12
PHYSICS
Four Screw guages are given (A) Pitch...

Four Screw guages are given
(A) Pitch = 1 mm, no. of division circular scale = 100
(B) Pitch = 1/2 mm, no. of division circular scale = 70
(C) Three Pitch = 4 mm, no. of division circular scale = 100
(D) Six Pitch = 5 mm, no. of division circular scale = 50

A

`A lt B lt C lt D`

B

`B lt A lt C lt D`

C

`D lt Clt A lt B`

D

`D lt C lt B lt A`

Text Solution

AI Generated Solution

Promotional Banner

Topper's Solved these Questions

Similar Questions

Explore conceptually related problems

Pitch of a screw gauge is 0.5 mm and its least count is .01 mm, Calculate no. of divisons on its circular scale.

A screw gauge with a pitch of 1 mm has 100 divisions on its circular scale. What it is used to measure the diameter of a thin wire, the main scale reading is 3 mm and the circular scale reading is 45. If D is the diameter of the wire in mm, then find the value of D.

A screw gauge has 1.0mm pitch and 200 divisions on the ciruclar scale. The least count of the instrument is

In a complete rotation, spindle of a screw gauge advances by (1)/(2)mm . There are 50 divisions on circular scale. The main scale has (1)/(2)mm marks to (is graduated to (1)/(2)mm ) If a wire is put between the jaws, 3 main scale divisions are clearly visible, and 20th division of circular scale coincides with reference line. Find diameter of wire in correct significant figures.

A screw gauge has least count of 0.01 mm and there are 50 divisions in its circular scale: The pitch of the screw gauge is:

The pitch of a screw gauge is 0.5 mm and the number of division on the circular scale is 100. When a glass plate is held between the studs of the screw gauge , the main scale reads 1.5 mm and the 69th division of the circular scale coincides with the index line of the main scale . What is the thickness of the glass plate ?

A screw gauge advances by 3mm in 6 rotations. There are 50 divisions on circular scale. Find least count of screw gauge

Answer the following : (a) You are given a tread and a metre scale. How will you estimate the diameter of the thread ? (b) A screw gauge has a pitch of 1.0 mm and 200 divisions on the circular scale. Do you think it is possible to increase the accuracy of the screw gauge arbitratily by increasing the number of divisions on the circular scale ? (c) The mean diameter of a thin brass rod is to be measured by vernier callipers. Why is a set of 100 measurements of the diameter expected to yield a more reliable estimate than a set of 5 measurement only ?

ALLEN-TEST PAPER 2-PHYSICS
  1. A wire is stretched 30%, what is the % change in its resistance?

    Text Solution

    |

  2. Calculate the resistance of a hollow cylindrical pipe of inner and out...

    Text Solution

    |

  3. The resistance of each side of an equilateral triangle is 6 ohm. Calcu...

    Text Solution

    |

  4. Find the effective resistance between points A and B for the network s...

    Text Solution

    |

  5. In the given figure when the key is open the ammeter reading is 5 amp....

    Text Solution

    |

  6. The average translational kinetic energy of the molecules of a gas wil...

    Text Solution

    |

  7. Four molecules of a gas have speed 1, 2, 3 and 4 km s^(-1) respectivel...

    Text Solution

    |

  8. At what temperature, rms velocity of O(2) molecules will be 1//3 of H(...

    Text Solution

    |

  9. Figure shows graphs of pressure vs density for an ideal gas at two tem...

    Text Solution

    |

  10. During an experiment an ideal gas is found to obey an additional law V...

    Text Solution

    |

  11. Q cal of heat is required to raise the temperature of 1 mole of a mona...

    Text Solution

    |

  12. When an ideal diatomic gas is heated at constant pressure, the fractio...

    Text Solution

    |

  13. When 1 mole of a monatomic gas is mixed with 3 moles of a diatomic gas...

    Text Solution

    |

  14. Internal energy of an ideal gas depends upon : -

    Text Solution

    |

  15. Calculate the work done by the gas in the state diagram shown :

    Text Solution

    |

  16. A = x + y and B = xy x = (20 pm1) cm , y = (10 pm 1) cm Then whic...

    Text Solution

    |

  17. Four Screw guages are given (A) Pitch = 1 mm, no. of division circu...

    Text Solution

    |

  18. Which of the following is supplementry unit

    Text Solution

    |

  19. If Pressure, mass and velocity are fundamental physical quantities, th...

    Text Solution

    |

  20. Which of the following is fundamental vector quantity.

    Text Solution

    |