The surface of water in contact with gla...

The surface of water in contact with glass wall is

plane

concave

convex

both 'b' and 'c'

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

SURFACE TENSION
NIKITA PUBLICATION|Exercise Multiple Choice Questions (Excess pressure due to surface tension )|64 Videos
STATIONARY WAVES
NIKITA PUBLICATION|Exercise MCQs|396 Videos
WAVE MOTION
NIKITA PUBLICATION|Exercise Multiple Choice Questions|364 Videos

Similar Questions

Explore conceptually related problems

Assertion :The contact angle between water and glass is acute. Reason :The surface of water in the capillary is convex .

The top of a lake is frozen when the air in contact with the lake surface is at -5^(@)C the temperature of water in contact with the bottom of the lake will be

A glass capillary tube is held vertical and put into contact with the surface of water in a tank. It was observed that the liquid rises to the top of the tube before settling to an equilibrium height h_(0) in the tube. Assume that water perfectly wets glass and viscosity is small. Is the length of the capillary tube larger then 2h_(0) ?

Water glass is :

The angle of contact between glass and water is 0^@ and water (surface tension 70 dyn//cm ) rises in a glass capillary up to 6 cm . Another liquid of surface tension 140 dyn//cm , angle of contact 60^@ and relative density 2 will rise in the same capillary up to

Consider the situation shown in figure. The wall and the surface of A and B in contact are rough. The friction on A due to .

A glass U-tube is such that the diameter of one limb is 3.0mm and that of the other is 6.0mm. The tube is inverted vertically with the open ends below the surface of water in a beaker. What is the difference between the height to which water rises in the two limbs? Surface tension of water is 0.07Nm^(-1) . Assume that the angle of contact between water and glass is 0^(@) .

A 3-kg steel ball strikes a wall with a speed of 10.0ms^(-1) at an angle of 60.0^(@) with the surfaces of the wall. The ball bounces off with the same speed and same angle. If the ball was in contact with the wall for 0.2s, find the average force exerted by the wall on the ball.

NIKITA PUBLICATION-SURFACE TENSION-Multiple Choice Questions (Question Given in MHT-CET )

If the surface of a liquid is plane, then the angle of contact of the ...
Text Solution
|
Work done is blowing a soap bubble of diameter 2 cm , is
Text Solution
|
The surface of water in contact with glass wall is
Text Solution
|
Work done in forming a liquid drop of radius R is W(1) and that of rad...
Text Solution
|
For liquid to rise in a capillary tube , the angle of contact should b...
Text Solution
|
Out of the following , which is not an example of capillary action
Text Solution
|
If a liquid does not wet glass, its angle of contact is
Text Solution
|
The surface tension of soap solution is 0.035 N/m . The energy needed...
Text Solution
|
A square frame of length L is immersed in soap solution and taken ou...
Text Solution
|
The potential energy of molecule on the surface of a liquid as compare...
Text Solution
|
If NaCl is dissolved into water , then its surface tension
Text Solution
|
Absorption of water by filter paper is due to
Text Solution
|
S.I. Unit of surface tension is:
Text Solution
|
A spherical liquid drop of radius R is divided into eight equal drople...
Text Solution
|
The potential energy of molecule on the surface of a liquid as compare...
Text Solution
|
n' droplets of equal of radius r coalesce to form a bigger drop of rad...
Text Solution
|
A big drop of radius R is formed by 1000 small droplets of water, then...
Text Solution
|
In which of the following substances , surface tension increases with ...
Text Solution
|
The angle of contact for pure water and clean glass surface is
Text Solution
|
A liquid rises to a height of 1.8 cm in a glass capillary A another g...
Text Solution
|