Home
Class 12
PHYSICS
The backlash error can be elimintated in...

The backlash error can be elimintated in Searle's experiment, by rotating screw in

A

one direction

B

both of the two directions

C

any direction

D

fist clockwise and then in anticlockwise directions.

Text Solution

Verified by Experts

The correct Answer is:
A
Promotional Banner

Topper's Solved these Questions

  • ELASTICITY

    TARGET PUBLICATION|Exercise Competitive Thinking|69 Videos

  • ELASTICITY

    TARGET PUBLICATION|Exercise Evaluation test|14 Videos

  • ELASTICITY

    TARGET PUBLICATION|Exercise Evaluation test|14 Videos

  • CURRENT ELECTRICITY

    TARGET PUBLICATION|Exercise Evaluation Test|6 Videos

  • ELECTROMAGNETIC INDUCTION

    TARGET PUBLICATION|Exercise EVALUATION TEST|8 Videos

Similar Questions

Explore conceptually related problems

The backlashes error can be elliminated in Searle's experiment, by rotating screw in

Accidental error can be minimised by

In Searl's experiment a graph is plotted between

Instrumental error can be minimised by

Assertion (A): Backlash error can be minimised by turning the screw in one direction only when fine adjustment is done. Reason (R ): Backlash error is caused due to wear and tear or loose- fittings in screws.

Assertion (A): In searle's experiment, it is better to start the experiment with some initial load on the hanger. Reason (R ): In searle's experiment, it is desirable that wire is straight and no kinks are there.

How many number of wires are used in Searl's experiment for determining Young's modulus of elasticity ?

How can we increase the relative accuracy of measurement by a screw gauge ?

TARGET PUBLICATION-ELASTICITY-Critical Thinking
  1. A uniform rod of cross-section 4 mm^(2) is heated from 0^(@)C " to "1...

    Text Solution

    |

  2. A steel of Xkg-wt//m^(2) is applied to a wire whose Young's modulus is...

    Text Solution

    |

  3. A steel wire 2 mm in diameter is just stretched between two fixed poin...

    Text Solution

    |

  4. The ratio of lengths of two rods A and B of same material is 1:2 and t...

    Text Solution

    |

  5. The backlash error can be elimintated in Searle's experiment, by rotat...

    Text Solution

    |

  6. To lift a load by a metallic rope, its radius of cross-section should ...

    Text Solution

    |

  7. Which of the following relations is incorrect for the sag(delta) of be...

    Text Solution

    |

  8. A beam of metal supported at the two edges is loaded at the centre. Th...

    Text Solution

    |

  9. A wire fixed at the upper end stretches by length l by applying a forc...

    Text Solution

    |

  10. On stretching a wire, the elastic energy stored pre unit volume is

    Text Solution

    |

  11. If one end of a wire is fixed with a rigid support and the other end i...

    Text Solution

    |

  12. A wire of length L and cross sectional area A is made of a material of...

    Text Solution

    |

  13. A metal rod of Young's modulus 2xx10^(10)Nm^(-2) undergoes an elastic ...

    Text Solution

    |

  14. If the volume of the given mass of a gas is increased four times, the ...

    Text Solution

    |

  15. A steel wire of length 5 m and area of cross-section 4 mm^(2) is stret...

    Text Solution

    |

  16. One end of a long mettalic wire of length L is tied to the ceiling. T...

    Text Solution

    |

  17. A rubber cord has a cross -sectional area 1 mm^(2)and total unstretche...

    Text Solution

    |

  18. The average depth of indian Ocean is about 3000 m. The fractional comp...

    Text Solution

    |

  19. Forces of 100 N each are applied in opposite direction on the upper an...

    Text Solution

    |

  20. Assertion: If length of a rod is doubled, the breaking load remains th...

    Text Solution

    |