The length of a cyclinder is measured as...

The length of a cyclinder is measured as `5 cm` using a vernier calipers of least count `0.1mm`. The percentage error in the measured length is nerarly

`0.5%`

`2%`

`20%`

`0.2%`

Text Solution

Verified by Experts

The correct Answer is:

`(Delta l)/(l) xx 100`

Topper's Solved these Questions

UNITS AND MEASUREMENTS
NARAYNA|Exercise ILLUSTRATION|49 Videos
UNITS AND MEASUREMENTS
NARAYNA|Exercise ILLUSTRATIONS|12 Videos
UNITS AND MEASUREMENTS
NARAYNA|Exercise LEVEL-I (H.W)|39 Videos
TRANSMISSION OF HEAT
NARAYNA|Exercise LEVEL-II(C.W)|27 Videos
VECTORS
NARAYNA|Exercise LEVEL-II (H.W)|14 Videos

Similar Questions

Explore conceptually related problems

The length of a cyclinder is measured as 5 cm using a vernier calipers of least count 0.1 mm. The percentage error in the measured length is nearly

Thickness of a cylinder measured using a screw gauge of least count 0.01cm is found to be equal to 0.80cm .The percentage error in measurement is

If the length of a cylinder is measured to be 4.28 cm with an error of 0.01cm , the percentage error in the mesured length is nearly

If the length of a cylinder is measured to be 8.28cm with an error of 0.01cm then the percentage error in measured length is nearly.

The length of a uniform rod is 100.0 cm and radius is 1.00 cm if length is measured with a meter rod having least count 1mm and radus is measured with vernier callipers having least count 0.1 mm the percentage error in calculated volume of cylinder is

Thickness of a pencil measured by using a screw gauge (least count.001 cm) comes out to be 0.802 cm .The percentage error in the measurement is

Length of a thin cylinder as measured by vernier callipers having least count 0.01cm is 3.25cm and its radius of cross-section is measured by a screw gauge having least count 0.01mm as 2.75mm . The percentage error in the measurement of volume of the cylinder will be

The dimensions of a rectangular block measured with a vernier callipers having least count of 0.1mm is 5mmxx10mmxx5mm . The maximum percentage error in measurement of volume of the blcok is

NARAYNA-UNITS AND MEASUREMENTS-LEVEL-II (H.W)

The error in the measurement fo length of a simple pendulum is 0.1% an...
Text Solution
|
The length of a cyclinder is measured as 5 cm using a vernier calipe...
Text Solution
|
The diameter of a wire as measured by a screw gauge was found to be 1....
Text Solution
|
The number of particles is given by n = -D(n(2) - n(1))/( x(2) - x(1))...
Text Solution
|
The external and internal diameter of a hollow cylinder are determine...
Text Solution
|
The density of a cube is measured by measuring its mass and length of ...
Text Solution
|
The diameter of a sphere is 3.34 m. Calculate its volume with due rega...
Text Solution
|
The length , breath and thickness of a metal sheet are 4.234m, 1.005m,...
Text Solution
|
The sides of a rectangle are (10.5 +- 0.2) cm and ( 5.2 +- 0.1 ) cm. C...
Text Solution
|
If the ratio of fundamental units in two systems are 2:3 the ratio of...
Text Solution
|
If L, R , C , and V, respectively , represent inductance , resistance ...
Text Solution
|
Hydrostatic pressure 'P' varies with displacement 'x' as P = (A)/(B) ...
Text Solution
|
The units of force, velocity and energy are 100 "dyne", 10 cm s^(-1) ...
Text Solution
|
The ratio of SI unit to CGS unti of gravitational constant of
Text Solution
|
The frequency f of vibrations of a mass m suspended from a spring of s...
Text Solution
|
If the period 'T' of a drop under surface tension 's' is given by T =...
Text Solution
|
If the velocity (V) , acceleration (A) , and force (F) are taken as fu...
Text Solution
|
The time dependence of a physical quantity P is given by P = P(0)e^(-a...
Text Solution
|
The value fo x in the formula Y = (2mg l^(x))/(5bt^(3)e) where m is th...
Text Solution
|
The velocity of sound in air (V) pressure (P) and density of air (d)...
Text Solution
|