A wire elongastes by 1.0 mm when a load ...

A wire elongastes by 1.0 mm when a load W ils hung from it. If this wire goes over a pulley and two weights W each are hung at the two ends the elongation of the wire will be

`0.5mm`

`1mm`

`2mm`

`4mm`

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

MECHANICAL PROPERTIES OF SOLIDS
NARAYNA|Exercise LEVEL-I (C.W)|37 Videos
MECHANICAL PROPERTIES OF SOLIDS
NARAYNA|Exercise LEVEL-II (C.W)|32 Videos
MECHANICAL PROPERTIES OF SOLIDS
NARAYNA|Exercise LEVEL-II (H.W)|24 Videos
MECHANICAL PROPERTIES OF FLUIDS
NARAYNA|Exercise EXERCISE - III|30 Videos
MOTION IN A PLANE
NARAYNA|Exercise Level-II(H.W)|31 Videos

Similar Questions

Explore conceptually related problems

A wire elongates by l mm when a load W is hanged from it. If the wire goes over a pulley and two weights W each are hung at the two ends, the elongation of the wire will be (in mm)

A wire elongates by l units, when a load w is suspended from it . If the wirew gets over a pulley ( equally on both the sides ) and two weights w each are hung at the two ends, the elongation of wire (in units ) will be

When a weight W is hung from one end of a wire of length L (other end being fixed), the length of the wire increases by l . If the same wire is passed over a pulley and two weights W each are hung at the two ends,what will be the total elongation in the wire?

When a load W is hung from a wire, it extends by Deltal . The heat produced in the process is

A wire whose cross-sectional area is 2 mm^2 is stretched by 0.1 mm by a certain load, and if a similar wire of triple the area of cross-section is stretched by the same load, then the elongation of the second wire would be

When a load of 5kg is hung on a wire then extension of 30 cm take place then work done will be :-

A metal wire of length L is suspended vertically from a rigid support. When a bob of mass M is attached to the lower end of wire, the elongation of the wire is l:

One end of a uniform wire of length l and weight W is attached to a point in the roof and a weight W/2 is suspended from the lower end. If A is the area fo cross-section of the wire, then stress of the wire at its midpoint will be

When a load of 10 kg is hung from the wire, then extension of 2m is produced. Then work done by restoring force is

NARAYNA-MECHANICAL PROPERTIES OF SOLIDS-C.U.Q

As temperture increases the Young's modulus of the material of a wire
Text Solution
|
If stress is numbercially equal to young's modulus, the elongation wi...
Text Solution
|
A wire elongastes by 1.0 mm when a load W ils hung from it. If this wi...
Text Solution
|
A uniform rod of length L and mass M is pulled horizontally on a smoot...
Text Solution
|
The bulk modulus for an incompresssible liquid is
Text Solution
|
Shearing strain is expreseed by
Text Solution
|
Braking froce per unit area of cross section of a wire is called
Text Solution
|
The property of metals where by they could be drawn into thin wires b...
Text Solution
|
The breaking stress of a wire depends on
Text Solution
|
A wire can sustain the weight of 40kg before breaking. If the wire is...
Text Solution
|
The graph shows the change 'Delta l' in the length of a thin uniform w...
Text Solution
|
If the length of the wire is doubled the strain produced is
Text Solution
|
A Copper wire and steel of the same diameter and length are connected...
Text Solution
|
An iron bar of length L. Cross section A and Young's modulus Y is heat...
Text Solution
|
Three wires A,B,C made of the same material and radius have different ...
Text Solution
|
According to Hooke's law of elasticity the ratio of stress too strain
Text Solution
|
The law which governs the working of a spring balance is
Text Solution
|
A body subjected to strain a number of times does not they Hook's la...
Text Solution
|
A heavy mass is attached to a thin wire and is whirled in a vertical c...
Text Solution
|
Steel is preferred for making springs over copper because
Text Solution
|