Consider the situation shown in figure. ...

Consider the situation shown in figure. The force F is equal to the `m_2g/2`. If the area of cross section of the string is A and its Young modulus Y, find the strain develolped in it. The string is lilght and there is no friction anywhere.

Text Solution

Verified by Experts

The correct Answer is:

`(m_(2)g(2m_(1)+m_(2)))/(2AY(m_(1)+m_(2)))`

Topper's Solved these Questions

DAILY PRACTICE PROBLEMS
RESONANCE|Exercise dpp 89 illustration|5 Videos
DAILY PRACTICE PROBLEMS
RESONANCE|Exercise dpp 90 Illustration|2 Videos
DAILY PRACTICE PROBLEMS
RESONANCE|Exercise dpp 88|7 Videos
CURRENT ELECTRICITY
RESONANCE|Exercise Exercise|54 Videos
ELASTICITY AND VISCOCITY
RESONANCE|Exercise Advanced Level Problems|9 Videos

Similar Questions

Explore conceptually related problems

Consider the situation shown in figure. The force F is equal to mg. If area of cross-section of the string is A and its Young's modulus is Y, the strain developed in the wire is (the string is light and there is no friction anywhere)

Consider the situation shown in figure. Find the acceleration of the system and the tension in the strings.

Consider the situation shown in the figure. The surface is smooth and the string and the pulley are light. Find the acceleration of each block and tension in the string.

Consider the situation shown in figure. All the surface are smooth. The tension in the string connected to 2m is.

Consider the situation shown in figure. All the surfaces are frictions and the string and the pulley are light. Find the magnitude of the acceleration of the two blocks.

Two wires have identical lengths and areas of cross-section are suspended by mass M . Their Young's modulus are in the ratio 2:5 .

The area of a cross section of steel wire is 0.1cm^2 and Young's modulus of steel is 2xx10^(11)Nm^-2 . The force required to strech by 0.1% of its length is

Consider4 the situation shown in figure. Bothe the pulleys and the string are light and all the surfaces are friction less. a. Find the acceleration of the mass M. b. Find the tension in the string c. Calculate the force exerted by the clamp on the pulley A in the figure.

RESONANCE-DAILY PRACTICE PROBLEMS-Now answer the following :

A wire elongastes by 1.0 mm when a load W ils hung from it. If this wi...
Text Solution
|
The length of a metal wire is l(1) when the tension in it is T(1) and ...
Text Solution
|
A heavy mass is attached to a thin wire and is whirled in a vertical c...
Text Solution
|
Two wires of equal length and cross sectional area suspended as shown ...
Text Solution
|
A steel wire and a copper wire of equal length and equal cross- sectio...
Text Solution
|
A steel rod of cross sectional area 4cm^2 and length 2m shrinks by 0.1...
Text Solution
|
Consider the situation shown in figure. The force F is equal to the m2...
Text Solution
|
If in a wire of Young's moduls Y, longitudinal strain X is produced th...
Text Solution
|
A metal wire of length L is suspended vertically from a rigid support....
Text Solution
|
A metal wire of length L, area of cross-section A and young's modulus ...
Text Solution
|
Two wires of the same material and length but diameters in the ratio 1...
Text Solution
|
The workdone in increasing the length of a one metre long wire of cro...
Text Solution
|
One end of a long metallic wire of length (L) is tied to the ceiling. ...
Text Solution
|
In the figure shown the straing versus stress graph for two values of...
Text Solution
|
A metal square plate of 10cm side rests on 2mm thick caster oil layer....
Text Solution
|
A man starts rowing his stationary cuboidal boat of base area A=10m^(2...
Text Solution
|
As per the shown figure the central solid cylinder starts with initial...
Text Solution
|
A ball bearing of radius of 3mm made of iron of density 7.85g cm^(-3) ...
Text Solution
|
An air bubble of 1cm radius is rising at a steady rate of 0.5cms^(-1) ...
Text Solution
|
A metallic sphere of radius 1.0 xx 10^(-3) m and density 1.0 xx 10^(4)...
Text Solution
|