If the friction is sufficient to prevent...

If the friction is sufficient to prevent the block from sliding, then the minimum value of F for which the cube begins to topple about an edge is

`(2)/(3)mg`

`(3)/(4)mg`

`(1)/(2)mg`

`mg`

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

NEET MOCK TEST 20
NTA MOCK TESTS|Exercise PHYSICS|45 Videos
NEET MOCK TEST 3
NTA MOCK TESTS|Exercise PHYSICS|45 Videos

Similar Questions

Explore conceptually related problems

A uniform cube of side and mass m rests on a rough horizontal surface. A horizontal force F is applied normal to one face at point that is directly above the centre of the face at a height (a)/(4) above the centre. The minimum value of F for which the cube begins to topple above an edge without sliding is

A uniform cube of side a and mass m rests on a rough horizontal table. A horizontal force F is applied normal to one of the faces at a point directly above the centre of the face, at a height (3a)/(4) above the base. What is the minimum value of F for which the cube begins to tip about an edge?

A cubical block of edge length 1 m and density 800 kg m^-3 rests on a rough horizontal surface with coefficient of friction mu . A horizontal force F is applied on the block as shown in figure. If the coefficient of friction is sufficiently large so that the block does not slide bofore toppling, then the minimum value of F to topple the block is [Take g = 10 ms^-2 ]

A cubical block of side a and of mass m rests on a rough horizontal surface. A horizontal force F is applied to normal to one of the faces at height h above the base hgta//2 . What is the minimum value of F for which the cube begins to tip about an edge?

A uniform cube of side a and mass m rests on a rough horizontal table. A horizontal force F is applied normal to one of the faces at a point that is directly above the centre of the face, at a height 3a/4 above the base. The minimum value of F which the cube begins to tip about the edge is ....(Assume that the cube does not slide).

An equilateral prism of mass m rests on a rough horizontal surface with cofficent of friction mu . A horizontal force F is applied on the prism as shown in the figure. If the cofficent of the friction is sufficently high so that the prism does not slide before toppling, then the minimum force required to topple the prism is

A cubical block of side L rests on a rough horizonta surface with coefficient of friction mu . A horizontal force F is applied on the block as shown. If the coefficient of friction is sufficiently high so that the block does not slide before toppling, the minimum force required to topple the block is

NTA MOCK TESTS-NEET MOCK TEST 21-PHYSICS

The angular velocity of a body is vec(omega)=2hati+3hatj+4hatk and a t...
Text Solution
|
The potential energy of a particle of mass 5 kg moving in the x-y plan...
Text Solution
|
If the friction is sufficient to prevent the block from sliding, then ...
Text Solution
|
A uniform cylinder rolls down from rest, on a track whose vertical cro...
Text Solution
|
A magnetic dipole is situated in the direction of a magnetic field. Wh...
Text Solution
|
A projectile is thrown with a velocity of 20 m//s, at an angle of 60^(...
Text Solution
|
A sample contains large number of nuclei. The probability that a nucle...
Text Solution
|
Photoelectric emission is observed from a metallic surface for frequen...
Text Solution
|
In a compound microscope, the focal lengths of two lenses are 1.5 cm a...
Text Solution
|
When a ray is refracted from one medium into another, the wavelegths c...
Text Solution
|
A 100 V a.c. source of frequency 500 Hz is connected to a LCR circuit ...
Text Solution
|
A rod of length l rotates with a small but uniform angular velocity om...
Text Solution
|
In the figure, which of the diode is in reverse bias
Text Solution
|
In the figure shown below each battery has emf = 5 V. Then the magneti...
Text Solution
|
Two long parallel wires are 30 cm apart carrying currents 10 A and 15 ...
Text Solution
|
The resistance of a moving coil galvanometer is 20Omega. It requires 0...
Text Solution
|
Consider the situation shown in the figure. The wire "AB" is sliding o...
Text Solution
|
The coefficient of friction between two surface is 0.2. The maximum an...
Text Solution
|
The ratio of thermal conductivity of two rods of different material is...
Text Solution
|
A dielectric slab is inserted between the plates of an isolated capaci...
Text Solution
|