A liquid is contained in a vertical tube...

A liquid is contained in a vertical tube a semicircular cross section the contact angle is zero. The force of surface tension on the curved part & on the flat part are in ratio

`1:1`

`1:2`

`pi : 2`

`2 : pi`

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

PROPERTIES OF MATTER
SURA PUBLICATION|Exercise Additional Questions (III. Fill in the blanks)|10 Videos
PROPERTIES OF MATTER
SURA PUBLICATION|Exercise Additional Questions (IV. Choose The ODD One Out)|3 Videos
PROPERTIES OF MATTER
SURA PUBLICATION|Exercise V. Conceptual Questions :|5 Videos
OSCILLATIONS
SURA PUBLICATION|Exercise VALUE BASED QUESTIONS|2 Videos
PUBLIC EXAM QUESTION PAPER MARCH-2019
SURA PUBLICATION|Exercise Part-IV|10 Videos

Similar Questions

Explore conceptually related problems

A uniform vertical tube of circular cross section contains a liquid. The contact angle is 90^@ . Consider a diameter of the tube lying in the surface of the liquid. The surface of the right of this diameter pulls the surface on the left of it. What keeps the surface on the left in equilibrium?

Water leaks out from an open tank through a hole of area 2mm^2 in the bottom. Suppose water is filled up to a height of 80 cm and the area of cross section of the tankis 0.4 m^2 . The pressure at the open surface and the hole are equal to the atmospheric pressure. Neglect the small velocity of the water near the open surface in the tank. a. Find the initial speed of water coming out of the hole. b. Findteh speed of water coming out when half of water has leaked out. c. Find the volume of water leaked out during a time interval dt after the height remained is h. Thus find the decrease in height dh in term of h and dt. d. From the result of part c. find the time required for half of the water to leak out.

Water at 50^(@)C is filled in a closed cylindrical vessel of height 10cm and cross sectional area 10cm^(2) The walls of the vessel are adiabatic but the flat parts are made of 1-mm thick aluminium (K=200Js^(-2)m^(-1)C^(-1) . Assume that the outside temperature is 20^(@)C . The density of water is 1000kgm^(-3) and the specify heat capacity of water =4200Jkg^(-1)C^(-1) .Estimate the time taken for the temperature to fall by 1.0^(@)C . Make any simplifying assumption you need but specify them.

Figure shows a small block of mass m which is started with a speed v on the horizontal part of the bigger block of mas m placed on a horizontal floor. The curved part of the surface shown is semicircular. All the surfaces are frictionless. Find the speed of the bigger block when the smaller block reaches the point A of the surface.

Suppose the tube in the previous problem is kep vertical with A upward but the other conditions remain the same. The separation between the cross sections at A and B is 15/16 cm. Repeat parts a., b, and c of the previous problem. take g=10ms^-2 .

The lower end of a capillary tube of radius 1 mm is dipped vertically into mercury. (a) Find the depression of mercury column in the capillary. (b) If the length dipped inside is half the answer of part (a), find the angle made by the mercury surface at the end of the capillary with the vertical. Surface tension of mercury =0.465Nm^-1 and the contact angle of mercury with glass =135^@ .

Water rises in a capillary tube to a certain height such that the upward force due to the durface tension is balanced by 62.84 xx 10^(-5)N force due to the weight of the liquid column. If the surface tension of water is 70 xx 10^(-3) Nm the radius of the capillary tube is

A thin tube of uniform cross section is sealed at both ends. It lies horizontally, the middle 5cm containing mercury and the parts on its two sides containing air at the same pressure p. when the tube is held at and angle of 60_(@) with the vertical, the length of the air column above and belw the mercury pellet are 46cm and 44.5cm respectively. Calculate the ressure - in centimeters of mercury, The timperature of the system is kept at 30_(@)C .

The lower end of a capillary tube is dipped into water and it is seen that the water rises through 7.5 cm in the capillary. Find the radius of the capilary. Surface tension of water =7.5xx10^-2Nm^-1 . Contact angle between water and glass =0^@. Take g=10ms^-2 .

SURA PUBLICATION-PROPERTIES OF MATTER-Additional Questions (I. Multiple Choice Questions :)

Water flows throw 2 identical tubes A & B, A volume V(0) of water poss...
Text Solution
|
Water is flowing in streamline motion throw a tube with its axis horiz...
Text Solution
|
There is a small hole near the bottom of an open tank filled with a li...
Text Solution
|
When a metal wire is stretched by a load the fractional change in its ...
Text Solution
|
When water droplets merge to form a bigger drop
Text Solution
|
Air is pushed into a soap bubble of radius r to double its radius, of ...
Text Solution
|
If more air is pushed in a soap bubble, the pressure in it will
Text Solution
|
If two soap bubbles of different radii are connected by a tube, then
Text Solution
|
The excess pressure inside a soap bubble is twice the excess pressure ...
Text Solution
|
Water rises in a vertical capillary tube upto a length of 10 cm if the...
Text Solution
|
Viscosity is a property of
Text Solution
|
The force of viscosity is
Text Solution
|
The viscous force acting between 2 layers of a liquid is given by (F)/...
Text Solution
|
A raindrop falls near the surface of the earth with almost uniform vel...
Text Solution
|
A piece of wood is taken deep inside a long column of water & released...
Text Solution
|
The rise of a liquid in a capillary tube depends on
Text Solution
|
The contact angle between a solid & a liquid is a property of
Text Solution
|
The properties of a surface are different from those of the bulk liqui...
Text Solution
|
When a capillary tube is dipped into a liquid the liquid neither rises...
Text Solution
|
A liquid is contained in a vertical tube a semicircular cross section ...
Text Solution
|