A cylinder of height 20 m is completely ...

A cylinder of height 20 m is completely filled with water. The velocity of efflux of water (in `ms^(-1)`) through a small hole on the side of the cylinder near its bottom is: `[g=10m//s^(2)]`

10 m/s

20 m/s

40 m/s

5 m/s

Text Solution

Verified by Experts

The correct Answer is:

Velocity of effux
`b=sqrt(2gh)`
`=sqrt(2xx10xx20)=sqrt(400)`
`=20m//s`

Topper's Solved these Questions

PROPERTIES OF MATTER
PREMIERS PUBLISHERS|Exercise OTHER IMPORTANT QUESTION & ANSWERS ( VERY SHORT ANSWER QUESTIONS )|36 Videos
PROPERTIES OF MATTER
PREMIERS PUBLISHERS|Exercise OTHER IMPORTANT QUESTION & ANSWERS (SHORT ANSWER QUESTIONS )|48 Videos
PROPERTIES OF MATTER
PREMIERS PUBLISHERS|Exercise EVALUTION TEXTBOOK QUESTIONS & ANSWERS (NUMERICAL PROBLEMS )|20 Videos
OSCILLATIONS
PREMIERS PUBLISHERS|Exercise OTHER IMPORTANT QUESTIONS & ANSWERS ( CONCEPTUAL QUESTIONS.)|24 Videos
QUESTION PAPER MARCH 2019
PREMIERS PUBLISHERS|Exercise Part- IV|23 Videos

Similar Questions

Explore conceptually related problems

The area of cross section of a large tank is 0.5m^2 . It has an opening near the bottom having area of cross section 1cm^2 . A load of 20 kg is applied on the water at the top. Find the velocity of the water coming out of the opening at the time when the height of water level is 50 cm above the bottom. Take g=10ms^-2

A stone dropped from the top of a tower of height 300m splashes into the water of a pond near the base of the tower. When is the splash heard at the top given that the speed of sound in air is 340ms^(-1) ? (g= 9.8ms^(-2))

A cylinder of length 1.5 m and diameter 4 cm is fixed at one end. A tangential force of 4 xx 10^(5) N is applied at the other end. If the rigidity modulus of the cylinder is 6 xx 10^(10) Nm^(-2) then, calculate the twist produce in the cylinder.

In a horizontal pipe of non-uniform cross section, water flows with a velocity of 1ms^(-1) at a point where the diameter of the pipe is 20 cm. The velocity of water (ms^(-1)) at a point where the diameter of the pipe 10 cm is:

A particle is thrown vertically upwards its velocity at half of the height is 10 m/s then the maximum height attained by it is ( g= 10 m//s^2)

PREMIERS PUBLISHERS-PROPERTIES OF MATTER-OTHER IMPORTANT QUESTION & ANSWERS (MULTIPLE CHOICE QUESTIONS )

An aeroplane gets its upward lift due to phenomenon described by the
Text Solution
|
In old age arteries carrying blood in the human body become narrow re...
Text Solution
|
Bernoulli's equation for steady, non-viscous, incompressible flow expr...
Text Solution
|
Water flows steadily through a horizontal pipe of variable cross-secti...
Text Solution
|
Calculate the force required to separate the glass plate of area of 10...
Text Solution
|
A cylinder of height 20 m is completely filled with water. The velocit...
Text Solution
|
A wind with speed 40 m/s blows parallel to the roof of a house. The a...
Text Solution
|
Four wires of the same material are stretched by the same load. The di...
Text Solution
|
Water is flowing throug a tube of radius r with velocity v. If the tub...
Text Solution
|
Which one of the following statements is wrong?
Text Solution
|
The increase in length of a wire on stretching is 0.025%. If its pois...
Text Solution
|
A metallic wire is stretched by suspending weight from it if alpha is ...
Text Solution
|
A copper wire of length 2.2 m and a steel wire of length 1.6m, both of...
Text Solution
|
The stress-strain curve for materials A and B are shown in figure. S...
Text Solution
|
Two wires of diameter 0.25 cm, one made of steel and the other made of...
Text Solution
|
The length of an iron wire is L and area of cross-section is A. The in...
Text Solution
|
k is the force constant of a spring. The work done in increasing its e...
Text Solution
|
If a liquid in a vessel is stirred and left to itself, the motion disa...
Text Solution
|
Copper of fixed volume V is drawn into a wire of length l. When this w...
Text Solution
|
In plotting stress versus strain curves for two materials P and Q, a s...
Text Solution
|