Home
Class 11
PHYSICS
Why is conversion of heat into work not ...

Why is conversion of heat into work not possible without a sink at lower temperature?

Promotional Banner

Topper's Solved these Questions

  • FLUIDS AT REST

    SL ARORA|Exercise Problem|19 Videos

  • FLUIDS AT REST

    SL ARORA|Exercise Problem for self practice|69 Videos

  • FLUIDS IN MOTION

    SL ARORA|Exercise All Questions|117 Videos

Similar Questions

Explore conceptually related problems

Is boiling of a liquid is possible without supplying heat?

A sink, that is a system where heat is rejected, is essential for the conversion of heat into work. From which law the above inference follows?

A reversible heat engine converts one-fourth of the heat input into work. When the temperature of the sink is reduced by 52 K, its efficiency is doubled. The temperature in Kelvin of the source will be _________.

A reversible engine converts one-sixth of the heat input into work. When the temperature of the sink is reduced by 62^@C , the efficiency of the engine is doubled. The temperatures of the source and sink are

A heat enegine works on a carnot cycle with a heat sink at a temperature of 2700K . The efficiency of the engine 10% . Determine the temperature of heat source.

A reversible engine converts one-sixth of the heat input into work. When the temperature of the sink is reduced by 62^ circ C , the efficiency of the engine is doubled the temperature of the source is

A Carnot engine converts one-fifth of heat given into work. If temperature of sink is reduced by 80^(@) , efficiency gets doubled. If temperature of sourceand sink is T_(1) and T_(2) respectively then calculate value of (T_(1)-T_(2))/(10)

SL ARORA-FLUIDS AT REST-Problem for self practice
  1. Why is conversion of heat into work not possible without a sink at low...

    Text Solution

    |

  2. A force of 40 N is applied on a nail , whose tip has an area of cross-...

    Text Solution

    |

  3. Atmospheric pressure is 1.01 xx 10^(5) Pa. How large a force does the ...

    Text Solution

    |

  4. The force on a Phonograph needle is 1.2 N. the point has a circular cr...

    Text Solution

    |

  5. A cylinderical vessel contaning liquid is closed by a smooth piston of...

    Text Solution

    |

  6. The cross-section of two piston in hydraulic press are 2cm^(2) "and" 1...

    Text Solution

    |

  7. The average mass that must be lifted by a hydraulic press is 80 "kg".I...

    Text Solution

    |

  8. In a hydraulic press used for compressing cotton the area of the pisto...

    Text Solution

    |

  9. An automobile sack is lifted by a hydraulic jack that consists of two ...

    Text Solution

    |

  10. What is the minimum pressure required to force blood from the heart to...

    Text Solution

    |

  11. A column of water 40 cm height supports a 30 cm column of an unknown l...

    Text Solution

    |

  12. If the water pressure gauge shows the pressure at ground floor to be 2...

    Text Solution

    |

  13. A cylinderical jar of cross-sectional area of 50 cm^(2) is filled with...

    Text Solution

    |

  14. Water is filled in a flask upto a height of 20cm. The bottom of the fl...

    Text Solution

    |

  15. The density of asir ner earth's surface is 1.3kgm^-3 and the atmospher...

    Text Solution

    |

  16. A vertical U-tube of uniform inner cross-section contains mercury in ...

    Text Solution

    |

  17. Two liquids of specific gravity 1.2 "and" 0.84 are poured into the l...

    Text Solution

    |

  18. The area of cross-section of the wider tube shown in fig., is 800cm^(2...

    Text Solution

    |

  19. A barometer kept in an elevator accelerating upwards reads 76 cm of Hg...

    Text Solution

    |

  20. How much will a body of 70 N weight in water if it displaces 20 ml of...

    Text Solution

    |

  21. A solid weighs 6 kg in air. If its density is 2000 "kg" m^(3) what wil...

    Text Solution

    |