A Brass stopper snuggly fits in the hole...

A Brass stopper snuggly fits in the hole of steel plate. To remove the stopper easily, the system

should be heated

should be cooled

may be heated or cooled

can not be removed by heating or cooling

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

THERMAL PROPERTIES OF MATTER
AAKASH SERIES|Exercise EXERCISE-IB|68 Videos
THERMAL PROPERTIES OF MATTER
AAKASH SERIES|Exercise EXERCISE-2|106 Videos
THERMAL PROPERTIES OF MATTER
AAKASH SERIES|Exercise ADDITIONAL PRACTICE EXERCISE (LEVEL - II) PRACTICE SHEET (ADVANCED) Integer/Subjective Type Questions|2 Videos
SYSTEM OF PARTICLES AND ROTATIONAL MOTION
AAKASH SERIES|Exercise PRACTICE EXERCISE|99 Videos
THERMODYNAMICS
AAKASH SERIES|Exercise EXERCISE - 3|33 Videos

Similar Questions

Explore conceptually related problems

(A) : A brass disc fits snugly in the hole of the iron plate. To remove the disc the combination must be heated. ( R) : The coefficient of linear expansion of brass is less than that of iron

A tightened glass stopper can be taken out easily by pouring hot water around the neck of the bottle as

If a cylinder of diameter 1.0cm at 30°c is to be slide into a hole of diameter 0.9997 cm in a steel plate at the same temperature, then minimum required rise in the temperature of the plate is [coefficient of linear expansion of steel = 12 xx 10^(-6) //^(@) C ]

Two capacitors A and B of capacities C and 2C are connected in parallel and the combination is connected to a battery of V volts. After the charging is over , the battery is removed. Now a dielectric slab of K=2 is inserted between the plates of A so as fill the completely. The energy lost by the system during the sharing of charges is (i) With battery of parallel combination :

A movable steel plate is placed between fixed steel and brass plates and the stack of plates is subjected to a weight of 100 N as shown in the figure. The coefficient of kinetic friction for steel on steel is 0.57 and for steel on brass is 0.44. Assuming that the entire weight comes onto the stack and that the weight of the plates is negligible in comparison to the applied weight, the force required to move the middle plate (in N) is

AAKASH SERIES-THERMAL PROPERTIES OF MATTER-EXERCISE-IA

When the temperature of a body increases
Text Solution
|
Two Brass rods of same length but with different diameters are heated ...
Text Solution
|
A Brass stopper snuggly fits in the hole of steel plate. To remove the...
Text Solution
|
A ball does not pass through a copper ring at room temperature. The sa...
Text Solution
|
A thick glass tumbler gets cracks when boiling water is poured into it...
Text Solution
|
Good quality glass tumblers are made of special material whose linear ...
Text Solution
|
Due to heating, soft rubber
Text Solution
|
A solid sphere and a hollow sphere of same material have same mass. Wh...
Text Solution
|
A metal meter scale has two holes at the two ends. when the scale is h...
Text Solution
|
In RCC slabs only iron rods are used but not of any other metal becaus...
Text Solution
|
Among the following solids, the lowest coefficient of expansion is for
Text Solution
|
If the length of a body is measured in centimeters instead of meters, ...
Text Solution
|
A solid ball of metall has a spherical cavity inside it. The ball is h...
Text Solution
|
A platinum wire can be sealed through glass, but a brass wire cannot b...
Text Solution
|
Two spheres of same size are made of same metal, but one is hollow and...
Text Solution
|
A metal washer has a hole of diameter d(1) and an external diameter d(...
Text Solution
|
A metal sphere is heated. Maximum percentage increase occurs in its
Text Solution
|
Thermostat works on the principle of
Text Solution
|
Two metal strips that constitute a thermostat must necessarly differ i...
Text Solution
|
A bimetal made of copper and iron strips welded together is straight a...
Text Solution
|