A student measured the diameter of a sma...

A student measured the diameter of a small steel ball using a screw gauge of least count `0.001 cm`. The main scale reading is `5 mm` and zero of circular scale division coincides with 25 divisions above the reference level. If screw gauge has a zero error of `-0.004 cm`, the correct diameter of the ball is

`0.521 cm`

`0.529cm`

`0.053` cm

`0.526` cm

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

MEASUREMENTS
TARGET PUBLICATION|Exercise COMPETITIVE THINKING ( MISCELLANEOUS)|6 Videos
MEASUREMENTS
TARGET PUBLICATION|Exercise EVALUATION TEST|17 Videos
MEASUREMENTS
TARGET PUBLICATION|Exercise COMPETITIVE THINKING ( DIMENSIONAL ANALYSIS)|43 Videos
MAGNETISM
TARGET PUBLICATION|Exercise MCQs|147 Videos
Motion in a plane
TARGET PUBLICATION|Exercise Exercise|340 Videos

Similar Questions

Explore conceptually related problems

When a screw gauge is comletely closed, zero of circular scale is 4 divisions abvoe the reference line of graduation. If L.C of screw gauge is 10^(-3) cm, the zero error is

Two full turns of the circular scale of a screw gauge cover a distance of 1 mm on its main scale . The total number of divisions on the circular scale is 50. Further more it is found that the screw gauge has a zero error of - 0.02 mm . While measuring the diameter of a thin wire , a student notes the main scale reading of 3 mm and the number of circular scale divisions in line with the main scale as 37. The diameter of the wire is

Two full turns of the circular scale of a screw gauge cover a distance of 1 mn on its its main scale . The total number of divisions on the circular scale is 50. Further m it is found that the screw gauge has a zero error of - 0.02 mm . While measuring the diameter of a thin wire , a student notes the main scale reading of 4 mm and the number of circular scale divisions in line with the main scale as 37. The diameter of the wire is

The density of a solid ball is to be determined in an experiment. The diameter of the ball is measured with a screw gauge, whose pitch is 0.5mm and there are 50 divisions on the circular scale. The reading on the main scale is 2.5mm and that on circular scale is 20 divisions. if the measured mass of the ball has a relative error of 2% , the relative percentage error in the density is

A screw gauge gives the following reading when used to mesure the diametre of a wire. Main scale reading : 0mm Circular scale reading : 52 divisions Given that 1mm on main scale corresponds to 100 divisions of the circular scale. the diameter of wire from the above data is :

Thickness of the paper mesaured by micrometer screw gauge of least count 0.01 mm is 1.03 mm, the percentage error in the measurement of thickness of paper is

The least count of a screw gauge is 0.005 cm . The diameter of wire is 0.02 cm as measured by it. The percentage error in measurement is

The jaws of a vernier callipers touch the inner wall of calorimeter without any undue pressure. The position of zero of vernier scale on the main scale reads 3.48 cm. The 6^(th) of vernier scale division is coinciding with any main scale division. Vernier constant of callipers is 0.01 cm. Find actual internal diameter of calorimeter, when it is observed that the vernier scale has a zero error of -0.03cm.

The thin metallic strip of vernier callipers moves downward from top to bottom in such a way that it just touches the surface of beaker. Main scale reading of calliper is 6.4 cm whereas its vernier constant is 0.1 mm. The 4^(th) of vernier scale division is coinciding with main scale division. The actual depth of berker in mm is (when zero of vernier coincides with zero of main scale)

A spectrometer gives the following reading when used to measure the angle of a prism. Main scale reading =58.5 degree Vernier scale reading =0.9 divisions Given that 1 divisions on main scale corresponds to 0.5 degree. Total divisions on the vernier scale is 30 and match with 29 divisions of the main scale. the angle of the prism from the above data is :

TARGET PUBLICATION-MEASUREMENTS-COMPETITIVE THINKING (ACCURAY AND ERRORS IN MEASUREMENTS)

Choose the INCOREET statement out of the folloiwng .
Text Solution
|
Assertion: The error in the measurement of radius of sphere is 0.3%. T...
Text Solution
|
If Y = a-b, the maximum percentage error in the measurement of Y will ...
Text Solution
|
The radius of a sphere is (5.3 +- 0.1)cm The percentage error in its v...
Text Solution
|
Resistance of a given wire is obtained by measuring the current flowin...
Text Solution
|
In an experiment four quantities a,b,c and d are measure with percenta...
Text Solution
|
Let x={:[(a^(2)b^(2))/(c)]:} be the physical quantity. If the percenta...
Text Solution
|
Two full turns of the circular scale of a screw gauge cover a distanc...
Text Solution
|
A screw gauge with a pitch of 0.5mm and a circular scale with 50 divis...
Text Solution
|
A student measured the diameter of a small steel ball using a screw ga...
Text Solution
|
The density of a solid ball is to be determined in an experiment. The ...
Text Solution
|
A force vecF applied on a square plate of length L. If the percent...
Text Solution
|
The density of a material in the shape of a cube is determined by meas...
Text Solution
|
In the determination if Young's modulus ((Y = (4MLg)/(pild^(2)) by usi...
Text Solution
|
If the time period of a simple pendulum is T = 2pi sqrt(l//g) , t...
Text Solution
|
A student measures the value of g with the help of a simple pendulu...
Text Solution
|
The period of oscillation of a simple pendulum is T = 2pisqrt((L)/(g))...
Text Solution
|
The following observations were taken for dtermining the surface tensi...
Text Solution
|