Home
Class 9
PHYSICS
When a screw gauge of least count 0.01 m...

When a screw gauge of least count 0.01 mm is used to measure the diameter of a wire, the reading on the sleeve is found to be 1 mm and the reading on the thimble is found to be 27 divisions.If the zero error + 0.005 cm, what is the correct diameter ?

Text Solution

AI Generated Solution

To find the correct diameter of the wire using the screw gauge measurements, we will follow these steps: ### Step-by-Step Solution: 1. **Identify the Least Count of the Screw Gauge**: - The least count (LC) of the screw gauge is given as 0.01 mm. - Convert this to centimeters: \[ ...
Promotional Banner

Topper's Solved these Questions

  • MEASUREMENTS AND EXPERIMENTATION

    ICSE|Exercise EXERCISE 1(C)|21 Videos

  • MEASUREMENTS AND EXPERIMENTATION

    ICSE|Exercise EXERCISE 1(C) (Mulitple Choice Type)|3 Videos

  • MEASUREMENTS AND EXPERIMENTATION

    ICSE|Exercise EXERCISE 1(B) (Multiple Choice Type)|3 Videos

  • MAGNETISM

    ICSE|Exercise EXERCISE-10(B) (Multiple Choice Type)|2 Videos

  • MOTION IN ONE DIMENSION

    ICSE|Exercise EXERCISE -2 (C) ( Multiple choice type :) |17 Videos

Similar Questions

Explore conceptually related problems

When a screw gauge of least count 0.01 mm is used to measure the diameter of a wire, the reading on the sleeve is found to be 1 mm and the reading on the thimble is found to be 27 divisions.What is the diameter of the wire in cm ?

The pitch of a screw gauge is 1mm and its cap is divided into 100 divisions. When this screw gauge is used to measure the diameter of a wire, then main scale reading is 2 mm and 58^(th) division of circular scale coincides with the main scale. There is no zero error in the screw gage. Then the diameter of the wire is

A student measued the diameter of a small steel ball using a screw gauge of least count 0.001 cm . The main scale reading is 5 mm and zero of circular scale division coincides with 25 divisions above the reference level. If screw gauge has a zero erroof -0.004 cm , the correct diameter of the ball is

A student measured the diameter of a wire using a screw gauge with least count 0.001cm and listed the measurement. The correct measurement is

A screw gauge has least count of 0.01 mm and there are 50 divisions in its circular scale: The pitch of the screw gauge is:

A screw gauge gives the following reading when used to mesure the diametre of a wire. Main scale reading : 0 mm Circular scale reading : 52 divisions Given that 1 mm on main scale corresponds to 100 divisions of the circular scale. the diameter of wire from the above data is :

A screw gauge has a least count 0.001 cm and zero error + 0.007 cm. Draw a neat diagram to represent it.

The pitch of a screw gauge is 1 mm and there are 100 divisions on the circular head. While measuring the diameter of a wire, the main scale reads 3 mm and the 55th division is in line with the base line. Find the diameter of the wire. Assume that the screw gauge is free from zero error.

A screw gauge with a pitch of 1 mm has 100 divisions on its circular scale. What it is used to measure the diameter of a thin wire, the main scale reading is 3 mm and the circular scale reading is 45. If D is the diameter of the wire in mm, then find the value of D.

The diameter of a wire as measured by a screw gauge was found to be 1.002 cm, 1.000 cm, 1.006 cm .The absolute error in the second reading is

ICSE-MEASUREMENTS AND EXPERIMENTATION -EXERCISE 1(B) (Numericals)
  1. A boy uses a vernier callipers to measure the thickness of his pencil....

    Text Solution

    |

  2. A vernier callipers has its main scale graduated in mm and 10 division...

    Text Solution

    |

  3. A vernier callipers has its main scale graduated in mm and 10 division...

    Text Solution

    |

  4. The main scale of a vernier callipers is calibrated in mm and 19 divis...

    Text Solution

    |

  5. The main scale of a vernier callipers is calibrated in mm and 19 divis...

    Text Solution

    |

  6. In a vernier callipers, there are 10 divisions on the vernier scale an...

    Text Solution

    |

  7. In a vernier callipers, there are 10 divisions on the vernier scale an...

    Text Solution

    |

  8. The pitch of a screw gauge is 0.5 mm and the head scale is divided in ...

    Text Solution

    |

  9. The circular head of a screw gauge is divided into 50 divisions and th...

    Text Solution

    |

  10. The circular head of a screw gauge is divided into 50 divisions and th...

    Text Solution

    |

  11. The pitch of a screw gauge is 1 mm and its circular scale has 100 divi...

    Text Solution

    |

  12. The pitch of a screw gauge is 1 mm and its circular scale has 100 divi...

    Text Solution

    |

  13. When a screw gauge of least count 0.01 mm is used to measure the diame...

    Text Solution

    |

  14. When a screw gauge of least count 0.01 mm is used to measure the diame...

    Text Solution

    |

  15. A screw gauge has 50 divisions on its circular scale and its screw mov...

    Text Solution

    |

  16. A screw gauge has 50 divisions on its circular scale and its screw mov...

    Text Solution

    |

  17. A screw gauge has 50 divisions on its circular scale and its screw mov...

    Text Solution

    |

  18. Fig. below shows the reading obtained while measuring the diameter of...

    Text Solution

    |

  19. Fig. below shows the reading obtained while measuring the diameter of...

    Text Solution

    |

  20. Fig. below shows the reading obtained while measuring the diameter of...

    Text Solution

    |