Resistance of a given wire is obtained b...

Resistance of a given wire is obtained by measuring the current flowing in it and the voltage difference applies across it. If the percentage errors in the measurement of the current and voltage difference are `3%` each then in the value of error in resistance of the wire is

`6%`

zero

`1%`

`3%`

Text Solution

Verified by Experts

The correct Answer is:

Topper's Solved these Questions

HYDROSTATICS, VISCOSITY AND SURFACE TENSION (HYDRODYNAMICS)
PATHFINDER|Exercise QUESTION BANK|198 Videos
KINEMATICS-I
PATHFINDER|Exercise QUESTION BANK|172 Videos

Similar Questions

Explore conceptually related problems

Resistance of a conductor is 200 Omega and the current through it is 10 mA,What is the potential difference across the two ends of the conductor?

If voltage difference remains same and resistance becomes half the current will be-

What is the maximum percentage error in the measurement of K,E.If the percentage errors in mass and speed are 2% and 3% respectively?

Percentage errors in the measurement of mass and speed are 2% and 3% respectively. Estimate the error while calculating kinetic energy.-

The potential difference across the ends of a wire has been measured to be (100 +- 5) volt and the current in the wire as (10 +- 0.2) ampere. What is the percentage error in the computed resistance of the wire?

A n-p-n transistor is connected to common emitter configuration in a given amplifier. A load resistance of 800 Omega is connected in the collector circuit and the voltage drop across it is 0.8 V. If the current amplification factor is 0.96 and the input resistance of the circuit is 192 Omega the voltage gain and the power gain of the amplifier will respectively be

Electric current C, measured by a galvanometer, is given by the equation C=k tan theta , where k is constant. Then the percentage error in the current corresponding to an error 0.7 percent in the measurement of theta when theta=45^(@) is -

Resistance of a conductor is twice that of another conductor and the potential differences between the two ends of the two conductors are same. Find the ratio of strengths of currents flowing, through them.

PATHFINDER-KINEMATICS - II-QUESTION BANK

The pitch of screw gauge is 1mm and there are 100 division on its cir...
Text Solution
|
Compute the following with regard to significant figures. 3.8xx0.125
Text Solution
|
Compute the following with regard to significant figures. (0.9996xx3.5...
Text Solution
|
The radius of the Earth is 6.37xx10^6m & its mass is 5.975xx10^(24) kg...
Text Solution
|
The radius of sphere is measured to be (2.1+-0.5)cm. Calculate the sur...
Text Solution
|
length of a rectangular path is 10.52 m and its width is only 0.041 m....
Text Solution
|
The period of oscillation of a simple pendulum is T=2pisqrt(L/g). Meas...
Text Solution
|
The current voltage relation of diode is given by I= (e^(1000v/T) -1) ...
Text Solution
|
In which of te following pairs the two physical quantities have differ...
Text Solution
|
A particle moves with constant acceleration along a straight line star...
Text Solution
|
A particle is moving uniformly in a circular path of radius r. when it...
Text Solution
|
If force (F) ,velocity(V) and time (T) are taken as fundamental units,...
Text Solution
|
Let [epsilon0] denote the dimensional formula of the permittivity of v...
Text Solution
|
Resistance of a given wire is obtained by measuring the current flowin...
Text Solution
|
If a wire is started to make if 0.1% longer ,its resistance will
Text Solution
|
The dimensions of (mu0epsilon0)^(-1/2) are
Text Solution
|
Consider a Vernier callipers in which each 1 cm on the main scale is d...
Text Solution
|
Planck's constant ,speed of light c and gravitational constant G are u...
Text Solution
|
In terms of potential difference V , electric current I, permittivity ...
Text Solution
|
In the determination of Young's modulus (Y = (4MLg)/n/d^2) by using Se...
Text Solution
|