Home
Class 12
PHYSICS
A resistance R is to be measured using a...

A resistance R is to be measured using a meter bridge. Student chooses the standard resistance S to be `100 Omega`. He finds the null point at `l_1 = 2.9 cm`. He is told to attempt to improve the accuracy. Which of the following is a useful way?

A

he should measure `l_1` more accurately.

B

He should change S to `1000 Omega` and repeat the experiment?

C

He should change S to `3 Omega` and repeat the experiment.

D

He should give up hope of a more accurate measurement with a meter bridge?

Text Solution

Verified by Experts

Promotional Banner

Similar Questions

Explore conceptually related problems

In a meter bridge, two unknown resistances R and S when connected in two gaps, give a null point at 40 cm from one end. What is the ratio of R and S?

An unknown resistance R_(1) is connected is series with a resistance of 10 Omega. This combination is connected to one gap of a meter bridge, while other gap is connected to another resistance R_(2) . The balance point is at 50 cm Now , when the 10 Omega resistance is removed, the balanced point shifts to 40 cm Then the value of R_(1) is.

The measurement of an unknown resistance R is to be carried out using wheatstone bridge(see Fig. EP 3.10). Two students perform an experiment in two ways. The first student takes R_2 = 10 Omega and R_1 = 5 Omega . The other student takes R_2 = 1000 Omega and R_1 = 500 Omega . In the standard arm, both takes R_3 = 5 Omega . Both find R = R_2/R_1 R_3 = 10 Omega within errors.

In a meter-bridge experiment with a resistance R_(1) in left gap and a resistance X in a right gap. null point is obtained at 40 cm from the left emf. With a resistance R_(2) in the left gap, the null point is obtainned at 50 cm from left hand. Find the position of the left gap is containing R_(1) and R_(2) in series.

In a meter-bridge experiment with a resistance R_(1) in left gap and a resistance X in a right gap. null point is obtained at 40 cm from the left emf. With a resistance R_(2) in the left gap, the null point is obtainned at 50 cm from left hand. Find the position of the left gap is containing R_(1) and R_(2) in parallel.

With two resistance R_1 and R_2 (>R_1) in the two gaps of a metre bridge the balance was found to be 1/3 m from the zero end. When a 6 Omega resistance is connected in series with the smaller of the two resistance, the point is shifted to 2/3 m from the same end, then R_1 and R_2 Find the resistance of the two wires.

Figure 3.35 shows a 2.0 V potentiometer used for the determination of internal resistance of a 1.5 V cell. The balance point of the cell in open circuit is 76.3 cm. When a resistor of 9.5 Omega is used in the external circuit of the cell, the balance point shifts to 64.8 cm length of the potentiometer wire. Determine the internal resistance of the cell. :

Figure 3.34 shows a potentiometer circuit for comparison of two resistances. The balance point with a standard resistor R = 10.0 Omega is found to be 58.3 cm, while that with the unknown resistance X is 68.5 cm. Determine the value of X. What might you do if you failed to find a balance point with the given cell of emf epsilon ? :

Figure 3.33 shows a potentiometer with a cell of 2.0 V and internal resistance 0.40 Omega maintaining a potential drop across the resistor wire AB. A standard cell which maintains a constant emf of 1.02 V (for very moderate currents upto a few mA) gives a balance point at 67.3 cm length of the wire. To ensure very low currents drawn from the standard cell, a very high resistance of 600 k Omega is put in series with it, which is shorted close to the balance point. The standard cell is then replaced by a cell of unknown emf epsilon and the balance point found similarly, turns out to be at 82.3 cm length of the wire. Is the balance point affected by the internal resistance of the driver cell?:

Figure shows a potentiometer with a cell of 2.0 V and internal resistance 0.40 Omega maintaining a potential drop across the resistor wire AB. A standard cell which maintains a constant emf of 1.02 V (for very moderate currents upto a few mA) gives a balance point at 67.3 cm length of the wire. To ensure very low currents drawn from the standard cell, a very high resistance of 600 k Omega is put in series with it, which is shorted close to the balance point. The standard cell is then replaced by a cell of unknown emf epsilon and the balance point found similarly, turns out to be at 82.3 cm length of the wire. What purpose does the high resistance of 600 kOmega have? :