Home
Class 12
PHYSICS
Assuming the length of a chain to be L a...

Assuming the length of a chain to be L and coefficient of static friction `mu`. Compute the maximum length of the chain which can be held outside a table without sliding.

Text Solution

Verified by Experts

Let y be the maximum length of the chain can be hold out side the table without sliding.
Length of chain on the table `=(L-y)`
Weight of part of the chain on table `W'=(M)/(L)(L-y)g`
Weight of hanging part of the chain `W=(M)/(L)yg`
For equilibrium: limiting force of friction=weight of hanging part of the chain
`muR=W rArrmuW=WrArrmu(M)/(L)(L-y)g=(M)/(L)ygrArrmuL-muy=yrArry=(muL)/(1+mu)`
Promotional Banner

Topper's Solved these Questions

  • NEWTONS LAWS OF MOTION

    ALLEN |Exercise EXERCISE-I|52 Videos
  • NEWTONS LAWS OF MOTION

    ALLEN |Exercise EXERCISE-II|112 Videos
  • NEWTONS LAWS OF MOTION

    ALLEN |Exercise EXERCISE-III|28 Videos
  • NEWTON'S LAWS OF MOTION & FRICTION

    ALLEN |Exercise EXERCISE (JA)|4 Videos
  • RACE

    ALLEN |Exercise Basic Maths (Wave Motion & Dopplers Effect) (Stationary waves & doppler effect, beats)|25 Videos

Similar Questions

Explore conceptually related problems

A block of mass is placed on a surface with a vertical cross section given by y=x^3/6 . If the coefficient of friction is 0.5, the maximum height above the ground at which the block can be placed without slipping is:

A uniform thin cylindrical disk of mass M and radius R is attaached to two identical massless springs of spring constatn k which are fixed to the wall as shown in the figure. The springs are attached to the axle of the disk symmetrically on either side at a distance d from its centre. The axle is massless and both the springs and the axle are in horizontal plane. the unstretched length of each spring is L. The disk is initially at its equilibrium position with its centre of mass (CM) at a distance L from the wall. The disk rolls without slipping with velocity vecV_0 = vacV_0hati. The coefficinet of friction is mu. The maximum value of V_0 for whic the disk will roll without slipping is-

A particle of mass m rests on a horizontal floor with which it has a coefficient of static friction mu . It is desired to make the body move by applying the minimum possible force F. Find the magnitude of F and the direction in which it has to be applied.

A particle of mass m rests on a horizontal floor with which it has a coefficient of static friction mu . It is desired to make the body move by applying the minimum possible force F. Find the magnitude of F and the direction in which it has to be applied.

A car is moving along a banked road laid out as a circle of radius r . (a) What should be the banking angle theta so that the car travelling at speed v needs no frictional force from tyres to negotiate the turn ? (b) The coefficient of friction between tyres and road are mu_(s) = 0.9 and mu_(k) = 0.8 . At what maximum speed can a car enter the curve without sliding toward the top edge of the banked turn ?

A disc of radius R is rotating with an angular omega_(0) about a horizontal axis. It is placed on a horizontal table. The coefficient of kinetic friction is mu_(k) . (a) What was the velocity of its centre of mass before being brought in contact with the table? (b) What happens to the linear velocity of a point on its rim when placed in contact with the table? (c) What happens to the linear speed of the centre of mass when disc is placed in contact with the table? (d) Which force is responsible for the effects in (b) and (c )? (e) What condition should be satisfied for rolling to being? (f) Calculate the time taken for the rolling to begin.

Two-wheeler can tilt while turning. But four-wheeler cannot. Estimate maximum safe speed of a four-wheeler on turn of radius 10m assuming coefficient of static friction between tires and the flat road to be 0.64 and acceleration due to gravity to be 10 m//s^(2) .

A long horizontal rod has a bead which can slide along its length and initially placed at a distance L from one end A of the rod. The rod is set in angular motion about A with constant angular acceleration alpha. if the coefficient of friction between the rod and the bead is mu , and gravity is neglected, then the time after which the bead starts slipping is

A 4.0 kg block is put on top of a 5.0kg block. In order to cause the top block to slip on the bottom one, a horizontal force of 12N must be applied to the top block. Assuming a friction less table the maximum horizontal force F which can be applied to the lower block so that the blocks, will move together should be

ALLEN -NEWTONS LAWS OF MOTION-SWOE
  1. Two bodies A and B of mass 5 kg and 10 kg contact with each other rest...

    Text Solution

    |

  2. A block of mass 1kg is at rest on a rough horizontal surface having co...

    Text Solution

    |

  3. Assuming the length of a chain to be L and coefficient of static frict...

    Text Solution

    |

  4. If the coefficient of friction between an insect and bowl is mu and th...

    Text Solution

    |

  5. A body of mass M is kept on a rough horizontal surface (friction coeff...

    Text Solution

    |

  6. A block rest on a rough inclined plane as shown in fig. A horizontal f...

    Text Solution

    |

  7. Two blocks of masses m(1)=1 kg and m(2)=2 kg are connected by a string...

    Text Solution

    |

  8. For shown situation draw a graph showing acceleration of A and B on y-...

    Text Solution

    |

  9. A block of mass m rests on a rough horizontl surface as shown in figur...

    Text Solution

    |

  10. A particle of mass m rests on a horizontal floor with which it has a c...

    Text Solution

    |

  11. A block of 1 kg is stopped against a wall by applying a force F perpen...

    Text Solution

    |

  12. A block A with mass 100kg is resting on another block B of mass 200kg....

    Text Solution

    |

  13. Consider the figure shown here of a moving cart C. if the coefficient ...

    Text Solution

    |

  14. A block of mass 1kg lies on a horizontal surface in a turck, the coeff...

    Text Solution

    |

  15. Coefficient of friction between two block shown in figure is mu = 0.4....

    Text Solution

    |

  16. A horizontal force of 10N is necessary to just hold a block stationary...

    Text Solution

    |

  17. Blocks A and B of masses 5 kg and 10kg are placed as shown in figure. ...

    Text Solution

    |

  18. If coeffiecient of friction between the block of mass 2kg and table is...

    Text Solution

    |

  19. If the momenta of two particles of a system are given by vecp(1)=2hati...

    Text Solution

    |

  20. A rocket fired from the earth's surface ejects 1% of its mass at a spe...

    Text Solution

    |