Home
Class 11
PHYSICS
If in a p-n junction, a square input sig...

If in a p-n junction, a square input signal of `10 V` is applied as shown,

then the output across `R_(L)` will be

A

B

C

D

Text Solution

Verified by Experts

The correct Answer is:
A
Promotional Banner

Topper's Solved these Questions

  • SEMICONDUCTORS

    ALLEN|Exercise Part-3(Exercise-3)|27 Videos

  • PHYSICAL WORLD, UNITS AND DIMENSIONS & ERRORS IN MEASUREMENT

    ALLEN|Exercise EXERCISE-IV|8 Videos

  • WAVES AND OSCILLATIONS

    ALLEN|Exercise Part-1(Exercise-05)[B]|42 Videos

Similar Questions

Explore conceptually related problems

If in a p-n junction, a square input signal of 10 V is applied as shwon, then the output across R_L will be

If a p-n junction diode, a square input signal of 10 V is applied as shown. Then the out put signal across R_(L) will be .

If in p-n junction diode a sinusoidal input signal is applied as shown Then the output signal across R_(L) will bw

input are given as shown then output signal is-

In a common emitter amplifier the input signal is applied across

A resistance R is connected at the n terminal of a p-n junction in series. An AC voltage is applied across this circuit. Which of the following are true for the circuit?

In a common emitter amplifier, using output reisistance of 5000 ohm and input resistance fo 2000 ohm, if the peak value of input signal voltage is 10 m V and beta=50 , then the peak value of output voltage is

The i-V characteristic of a p-n junction diode is shown in figure.Find the approximate dynamic resistance of the p-n junction when (a) a forward bias of 1 volt is applied ,(b) a forward bias of 2 volt is applied is applied .

The amplifiers X, Y and Z are connected in series. If the voltage gains of X, Y and Z are 10, 20 and 30 , respectively and the input signal is 1mV peak value, then what is the output signal voltage (peak value) (i) if dc supply voltage is 10V ? (ii) if dc supply voltage is 5V?

The amplifiers X, Y and Z are connected in series. If the voltage gains of X, Y and Z are 10, 20 and 30 , respectively and the input signal is 1mV peak value, then what is the output signal voltage (peak value) (i) if dc supply voltage is 10V ? (ii) if dc supply voltage is 5V?

ALLEN-SEMICONDUCTORS-Part-3(Exercise-4)
  1. If the lattice constant of this semiconductor is decreased, then which...

    Text Solution

    |

  2. Carbon, silicon and germanium have four valence electrons each. At roo...

    Text Solution

    |

  3. If in a p-n junction, a square input signal of 10 V is applied as show...

    Text Solution

    |

  4. A working transitor with its three legs marked P, Q and R is tested us...

    Text Solution

    |

  5. In the circuit below, A and B represent two inputs and C represents th...

    Text Solution

    |

  6. A p -n junction (D) shown in the figure can act as a rectifier. An alt...

    Text Solution

    |

  7. The logic circuit shown below has the input waveforems 'A' and 'B' as ...

    Text Solution

    |

  8. The combination of gates shown below yields

    Text Solution

    |

  9. The question has statement - 1 and statement - 2 Of the four choices ...

    Text Solution

    |

  10. The output of an OR gate is connected to both the inputs of a NAND gat...

    Text Solution

    |

  11. Which of following four alternatives is not correct? We need modulatio...

    Text Solution

    |

  12. Truth table for system of four NAND gates as shown in figure is

    Text Solution

    |

  13. A diode detector is used to detect an amplitude modulated wave of 60% ...

    Text Solution

    |

  14. The I - V characteristic of an LED is

    Text Solution

    |

  15. The forward biased diode connection among the following is

    Text Solution

    |

  16. A signal of 5 kHz frequency is amplitude modulated on a carrier wave o...

    Text Solution

    |

  17. In an unbiased p-n junction, holes diffuse from the P-region to n-regi...

    Text Solution

    |

  18. A 2 V battery is connected across AB as shown in the figure. The value...

    Text Solution

    |

  19. The value of the resistor , Rs needed in the DC voltage regulator circ...

    Text Solution

    |

  20. Choose the correct statement

    Text Solution

    |