Home
Class 12
PHYSICS
The main scale of a vernier callipers re...

The main scale of a vernier callipers reads in millimeter and its vernier is divided into 10 divisions which coincides with 9 divisions of the main scale. The reading for shown situation is found to be `(x//10)`mm. Find the value of x.
.

Text Solution

Verified by Experts

The correct Answer is:
6.9 mm
Promotional Banner

Topper's Solved these Questions

  • RACE

    ALLEN|Exercise Basic Maths (KINEMATICS)|59 Videos

  • RACE

    ALLEN|Exercise Basic Maths (NEWTONS LAWS OF MOTION)|46 Videos

  • RACE

    ALLEN|Exercise Basic Maths (VECTORS)|60 Videos

  • NEWTONS LAWS OF MOTION

    ALLEN|Exercise EXERCISE-III|28 Videos

  • SIMPLE HARMONIC MOTION

    ALLEN|Exercise Example|1 Videos

Similar Questions

Explore conceptually related problems

The man scale of a Vernier Callipers reads in millimeter and its vernier is divided into 10 divisions which coincides with 9 divisions of the main scale. The length of the object for situation is found to be (x/10) mm. Find the value of x.

The main scale of a vernier callipers reads in millimeter and its vernier is divided into ten divisions, which coincide with seven divisions of main scale. Further when a cylinder is tightly placed along its length between two jaws, it is observed that the zero of vernier scale just right to 32 division of main scale and fourth division of vernier scale coincides with the main scale. Then the measured value is 0.33Kcm . Find the value of K .

The main scale of vernier callipers reads in millmetre and its vernier is divided into 8 divisions, which coincide with 5 divisions of main scale . Then When two jaws of instrument touch each other the zero of the vernier coincide with the zero of main scale . A rod is tightly placed along its length between both jaws, it is observed that the zero vernier scale lies just left to 36^("th") division of main scale and fourth division of vernier scale coincide with the main scale. Then the measured value is

The main scale of a vernier calliper reads in mm and its vernier scale is divided into 8 divisions, which coincides with 7 divisions of the main scale. It was also observed that, when the two jaws are brought in contact, the zero of the vernier scale coincided with the zero of the main scale. The edge length of a cube is measured using this vernier calliper. The main scale reads 12 mm and 2^("nd") division of the vernier scale coincides with the main scale. The edge length (in mm) of the cube is

The least count of the main scale of vernier callipers is 1 mm. Its vernier scale is divided into 10 divisions and coincide with 9 division of the main scale. When jaws are touching each other, the 7^(th) division of main scale and zero of main scale. When this vernier is used to measure lenght of a cylinder the zero of the vernier scales between 3.1 cm and 3.2 cm and 4^(th) VSD coincider with a main scale division . The lehgth of the cylinder is : (VSD is vernier scale division)

1 cm on the main scale of a vernier callipers is divided into 10 equal parts. If 10 divisions of vernier coincide with 8 small divisions of main scale, then the least count of the calliper is.

1 cm on the main scale of a vernier calipers is divided into 10 equal parts. If 10 divisions of vernier coincide with 8 small divisions of main scale, then the least count of the caliper is.

Read the vermier 10 division of vermier scale are matching with 9 divisionsd of main scale

In a vernier callipers, one main scale division is x cm and n divisions of the vernier scale coincide with (n-1) divisions of the main scale. The least count (in cm) of the callipers is :-

A vernier callipers has 20 divisions on the vernier scale which coincide with 19 divisions on the main scale. The least count of the instrument is 0.1 mm. The main scale divisions are of

ALLEN-RACE-Basic Maths (Units, Dimensions & Measurements)
  1. If momentum (p) area (A) and time (t) are taken to be fundamental quat...

    Text Solution

    |

  2. Which of the following specification is most accurate ?

    Text Solution

    |

  3. If a,x,b are in A.P.,a,y,b are in G.P. and a,z,b are in H.P. such that...

    Text Solution

    |

  4. Two resistances are measured in ohm and are given as: R(1)=3Omegapm1...

    Text Solution

    |

  5. The percentage error in measurement of a physical quantity m, given by...

    Text Solution

    |

  6. The number of significant digits in 0.001001 is :-

    Text Solution

    |

  7. The sides of a rectangle are (10.5 +- 0.2) cm and ( 5.2 +- 0.1 ) cm. C...

    Text Solution

    |

  8. The Young modulus (Y) of a material is given by Y=(WL)/(pir^(2)l). If ...

    Text Solution

    |

  9. Which of the following measurement is most precise?

    Text Solution

    |

  10. What is the reading of micrometer screw gauge shown in figure

    Text Solution

    |

  11. In a vernier callipers N divisions of vernier scale coincide with N-1 ...

    Text Solution

    |

  12. A vernier callipers having 1 mai scale divison =0.1cm is designed to h...

    Text Solution

    |

  13. The circular scale of a screw gauge has 50. divisions and pitch of 0.5...

    Text Solution

    |

  14. The diameter of a cylinder is measured using a vernier callipers with ...

    Text Solution

    |

  15. Two full turns of the circular scale of a screw gauge cover a distance...

    Text Solution

    |

  16. The circular scale of a micrometer has 200 divisions and pitch of 2 mm...

    Text Solution

    |

  17. A good analogy for understanding accuracy and precision is to imagine ...

    Text Solution

    |

  18. Suppose, you are to take the measurements of the mass of a 50.0-gram s...

    Text Solution

    |

  19. The main scale of a vernier callipers reads in millimeter and its vern...

    Text Solution

    |

  20. The pitch of a screw gauge is 1mm and there are 100 divisions on the c...

    Text Solution

    |