Home
Class 14
GENERAL KNOWLEDGE
The difference in temperature between th...

The difference in temperature between the warm, black side and the cooler white side causes gasses to creep along the surface of the vanes. This effect is known as

A

Radiation creep

B

Nuclear creep

C

Thermal creep

D

Conduction creep

Text Solution

Verified by Experts

The correct Answer is:
C
Promotional Banner

Similar Questions

Explore conceptually related problems

Calculate the difference in temperature between two sides of an iron plate 20 m m thick, when heat is conducted at the rate of 6xx10^(5) cal/min/ m^(2) . K for metal is 0.2 cal s^(-1)cm^(-1).^(@)C^(-1)

A rectangular block of iron has dimension 1.2 cm xx 1.2cm xx 1.5cm . A potential difference is to be applied to the block between parallel sides and in such a way that those sides are equipotential surfaces. What is the resistance of the block if the two parallel sides are (1) the square ends (with dimensions 1.2 cm xx 1.2 cm) and (2) two rectangular sides (with dimensions 1.2cm xx 15cm)?

In natural convection, the fluid motion is caused due to density difference produced by temperature gradient. Statement II: In forced convection, the fluid is forced to flow along the solid surface by means of fans or pumps.

The peak emission from a black body at a certain temprature occurs at a wavelength of 9000 Å . On increase its temperature , the total radiation emmited is increased its 81 times. At the intial temperature when the peak radiation from the black body is incident on a metal surface , it does not cause any photoemission from the surface . After the increase of temperature, the peak from the black body caused photoemission. To bring these photoelectrons to rest , a potential equivalent to the excitation energy between n = 2 and n = 3 bohr levels of hydrogen atoms is required. Find the work function of the metal.

Peak emission from a black body at a certain temperature occures at a wavelength lambda. On increasing its temperature , total radiation emitted is increasing 16 times . At the initial temperature when peak radiation from the black body is incident on a metal surface , it does not cause photoemission from surface . After the increasing the peak radiation from black body caused photoemission. to bring these photoelectrons to rest, a potential equivalent to the excitation energy between n=2 to n=3 Bohr levels of hydrogen atom is required. if eork function of metal is 2.24eV , then value of lambda is [hc=12400eV-Å]

Water in a clean large cuboid aquarium forms a meniscus, as shown in the figure. The difference in height between the centre and the edge of the meniscus is h. Surface tension of water is S = 0.073 Nm^(-1) . Atmospheric pressure is P_0=10^5 N//m^2 . Angle of contact between the water and aquarium wall is zero. Answer the following 3 question above illustrated situation. For an aquarium with side walls of length l ,horizontal force on the volume of water enclosed by the dashed line and free surface, by one aquarium wall is

A flat bottomed metal tank of water is dragged along a horizontal floor at the rate of 20 ms^(-1) . The tank is of mass 20kg and contains 1000 kg of water and all the heat produced in the dragging is conducted to the water through the bottom plate of the tank. If the bottom plate has an effective area of conduction 1 m^2 and a thickness 5 cm and the temperature of the water in the tank remains constant at 50^(@)C , calculate the temperature of the bottom surface of the tank, given the coefficient of friction between the tank and the floor is 0.343 and K for the material of the tank is 25 cal m^(-1) s^(-1) K^(-1).

A flat bottomed metal tank filled with water is dragged along a horizontal floor at the rate of 20 m//s The tank is of mass 100 kg and contains 900 kg of water and all the heat produced in the dragging is conducted to the water through the bottom plate of the tank. If the bottom plate has an effective area of conduction 1m^(2) and thickness 5 cm and the temperature of water in the tank remains constant at 50^(@) C, calculate the temperature of the bottom surface of the tank. Given the coefficient of friction between the tank and the floor is 0.5 and K for the material of the tank is 100 J//m sec K.

The difference in lateral pressure, causes a spinning ball to take a curved path which is convex towards the greater pressure side, this effect is called.............