The density of a material in the shape o...

The density of a material in the shape of a cube is determined by measuring three sides of the cube and its mass. If the relative errors in measuring the mass and length are respectively 1.5% and 1% , the maximum error in determining the denstiy is

`4.5%`

0.06

`2.5%`

`3.5%`

Text Solution

Verified by Experts

Topper's Solved these Questions

QUESTION PAPER OF NEET 2018
CHHAYA PUBLICATION|Exercise PART-B (SECTION-II)|1 Videos
QUESTION PAPER OF NEET 2017
CHHAYA PUBLICATION|Exercise QUESTION PAPERS OF (NEET) (2017)|39 Videos
QUESTION PAPER OF WBCHSE 2019
CHHAYA PUBLICATION|Exercise PART- B (SECTION-II)|4 Videos

Similar Questions

Explore conceptually related problems

The density of the material of a cube can be estimated by measuring its mass and the length of one of its sides. If the maximum error in the measurement of mass and length are 0.3% and 0.2% respectively, the maximum error in the estimation of the density of the cube is approximately

If the error in the measurement of the radius of a circular disc is 2% the error in determining the area of the disc will be

If the error in measuring a side of a cube is 5% , find the percentage error in the computation of its volume.

Percentage errors in the measurement of mass and speed are 2% and 3% respectively. Estimate the error while calculating kinetic energy.-

In a circuit, the generation of heat depends on resistance,current and time for which the current fIows. If the error in measuring resistance, current and time are 1%, 2% and 1% respectiveIy, find the maximum percentage error in measuring the heat.

The length of a side of a cube is 10 cm , if an error of 0.05 cm is made in measuring the side find the differential of volume (dv) and the approximate error.

Define relative error and percentage error in a measurement .

If heat dissipated in a resistance can be determined from the relation: H = I^(2)Rt joule If the maximum error in the measurement of current resistance and time are 2%, 1% and 1% respectively, what would be the maximum error in the dissipated heat?

If any edge of a cube is increased 50%, Measure of increment of its volume is____

CHHAYA PUBLICATION-QUESTION PAPER OF NEET 2018-QUESTIONS

In a collinear collision, a particle with an initial speed v(0) strike...
Text Solution
|
The dipole moment of a circular loop carrying a current I, is m and th...
Text Solution
|
The density of a material in the shape of a cube is determined by meas...
Text Solution
|
On interchanging the resistances, the balance point of a metre bridge ...
Text Solution
|
In an ac circuit, the instantaneous emf and current are given by e = 1...
Text Solution
|
Two moles of an ideal monoatomic gas occupies a volume V at 27^(@)C. T...
Text Solution
|
A particle is moving with a uniform speed in a circular orbit of radiu...
Text Solution
|
The fundamental frequency in an open organ pipe is equal to the third ...
Text Solution
|
At what temperature will the rms speed of oxygen molecules become just...
Text Solution
|
The efficiency of an ideal heat engine working between the freezing po...
Text Solution
|
A carbon resistor of (47 pm 4.7)kOmega is to be marked with rings of d...
Text Solution
|
A set of n equal resistors, of value R each, are connected in series t...
Text Solution
|
A battery consists of a variable number n of identical cells (having i...
Text Solution
|
Unpolarised light is incident from air on a plane surface of a materia...
Text Solution
|
In young's double slit experiment. The separation d between the slits ...
Text Solution
|
An astronomical refracting telescope will have large angular magnifica...
Text Solution
|
An electron of mass m with an initial velocity vec(V) = V(0)hat(i) (V(...
Text Solution
|
For a radioactive material, half-life is 10 minutes. If initially ther...
Text Solution
|
When the light of frequency 2v(0) (where v(0) is threshold frequency )...
Text Solution
|
In a p-n junction diode, change in temperatue due to heating
Text Solution
|