Home
Class 12
PHYSICS
If the value of potential in an ac, circ...

If the value of potential in an `ac`, circuit is `10 V`, then the peak value of potential is

A

`10/(sqrt(2))`

B

`10sqrt(2)`

C

`20sqrt(2)`

D

`20/(sqrt(2))`

Text Solution

Verified by Experts

The correct Answer is:
B
`V_(0)=sqrt(2)V_(rms)=10sqrt(2)`
Promotional Banner

Topper's Solved these Questions

  • ALTERNATING CURRENT

    A2Z|Exercise AIIMS Questions|26 Videos

  • ATOMIC PHYSICS

    A2Z|Exercise Section D - Chapter End Test|30 Videos

Similar Questions

Explore conceptually related problems

if the effective value of A.C in a circuit is 10A, then the peak value of current a

The peak value of 220 a.c. is

The rms value of current in an ac circuit is 25 A, then peak current is

If an AC ammeter reads I A in an AC circuit, then the peak value of the current is

If E_(0) represents the peak value of the voltage in an ac circuit, the r.m.s. value of the voltage will be

The circuit shown in the figure is a series LCR circuit connected to an AC source. This circuit has many important applications in practical electronic systems. In the given circuit, L = 20 mH and frequency of applied alternating potential difference is omega = 8000 rad//s . Initial phase of applied potential difference has such a minimum value that initial value of instantaneous potential difference is half of is peak value while initial phase of current in the circuit has such a minimum value that initial value of instantaneous current equals its peak value. We also observe that current in the circuit leads the net voltage across the circuit. It is given that peak values of potential difference across R and L are I V_(R)( peak))= 25 V V(L)_(peak)= 20 V Instantaneous potential difference across the inductor can be expressed as

A2Z-ALTERNATING CURRENT-Section D - Chapter End Test
  1. A 280 ohm electric bulb is connected to 200V electric line. The peak v...

    Text Solution

    |

  2. An AC source is rated at 220V, 50 Hz. The time taken for voltage to ch...

    Text Solution

    |

  3. If the value of potential in an ac, circuit is 10 V, then the peak val...

    Text Solution

    |

  4. The maximum value of AC voltage in a circuit is 70V. Its r.m.s. value ...

    Text Solution

    |

  5. If instantaneous current is given by i=4 cos(omega t + varphi) amperes...

    Text Solution

    |

  6. In an AC circuit, peak value of voltage is 423 volts. Its effective vo...

    Text Solution

    |

  7. The power factor of an AC circuit having resistance (R) and inductance...

    Text Solution

    |

  8. An inductor of inductance L and ressistor of resistance R are joined i...

    Text Solution

    |

  9. Alternating current can not be measured by D.C. Ammeter because

    Text Solution

    |

  10. In a LCR circuit capacitance is changed from C to 2C. For the resonant...

    Text Solution

    |

  11. In an LCR series a.c. Circuit the voltage across each of hte component...

    Text Solution

    |

  12. For the circuit shown in the figure, the current through the inductor ...

    Text Solution

    |

  13. In a series LCR circuit, the voltage across the resistance, capacitanc...

    Text Solution

    |

  14. An ideal choke takes a current of 10 A when connected to an ac supply ...

    Text Solution

    |

  15. A direct current of 5 amp is superimposed on an alternating current I=...

    Text Solution

    |

  16. A group of electric lamps having a total power rating of 1000 watt is ...

    Text Solution

    |

  17. In a LCR circuit having L=8.0 Henry, C=0.5 mu F and R=100 ohm in serie...

    Text Solution

    |

  18. An alternating current source of frequency 100 Hz is joined to a combi...

    Text Solution

    |

  19. A 10 ohm resistance, 5 mH coil and 10mu F capacitor are joined in seri...

    Text Solution

    |

  20. A resistor R, an inductor L and a capacitor C are connected in series ...

    Text Solution

    |